*ma*would be about the same, but yet we still need to put in much more force. Why? And can we measure it?

The reason that honey is harder to stir is of course that the drag on our spoon depends on more than just the density of the fluid. The drag also depends on the viscosity of the fluid -- loosely speaking, how thick it is -- and the viscosity of honey is about 400 times that of water, depending on the conditions. In fact, a quick perusal of the Wikipedia article on viscosity shows that viscosities can vary by a fantastic amount -- some 13 orders of magnitude, from easy-to-move gases to thick pitch that behaves like a solid except on long time scales. The situation is even more complicated than this, as some fluids can have a viscosity that changes depending on the flow.

I wanted to find a way to measure the viscosities of the stuff around me, so I made the viscometer pictured below for about $1.75 (the vending machines in Clark Hall are pretty expensive). How? Well, I

My homemade viscometer, taking data on the viscosity of water. |

- Enjoyed the crisp, refreshing taste of Diet Pepsi from a 20 oz bottle (come on, sponsorships).
- Cut the top and bottom off the bottle, so all that was left was a straight tube.
- Mounted the bottle with on top of a small piece of flat plastic.
- Mounted a single-tubed coffee stirrer horizontally out of the bottle (I placed the end towards the middle of the bottle to avoid end effects).
- Epoxied or glued the entire edge shut.
- Marked evenly-spaced lines on the side of the bottle.

I can load my "sample" fluid in the top of the Pepsi bottle, and time how long it takes for the sample level to drop to a certain point. A more viscous fluid will take more time to leave the bottle, with the time directly proportional to the viscosity. (This is a consequence of Stokes flow and the equation for flow in a pipe. It will always be true, as long as my fluid is viscous enough and my apparatus isn't too big.)

So we're done! All we need to do is calibrate our viscometer with one sample, measure the times, and then we can go out and measure stuff in the world! No need to stick around for the boring calculations! We can do some fun science over the next few blog posts!

But this is a physics blog written by a bunch of grad students, so I'm assuming that a few of you want to see the details. (I won't judge you if you don't though.) If we think about the problem for a bit, we basically have flow of a liquid through a pipe (i.e. the coffee stirrer), plus a bunch of other crap which hopefully doesn't matter much.

We first need to think about how the fluid moves. We want to find the velocity of the fluid at every position. This is best cast in the language of vector calculus -- we have a (vector) velocity field

**at a (vector) position**

*u***. There are two things we know: 1) We don't (globally) gain or lose any fluid, and 2) Newton's laws**

*x**F=ma*hold. We can write these equations as the Navier-Stokes equations: \[ \vec{\nabla}\cdot \vec{u} = 0 \quad (1) \] \[ \ \rho \left( \frac {\partial \vec{u}} {\partial t} + (\vec{u}\cdot\vec{\nabla})\vec{u} \right) = - \vec{\nabla}p + \eta \nabla^2 \vec{u} \quad (2) \] The first equation basically says that we don't have any fluid appearing or disappearing out of nowhere, and the second is basically

*m*, except written per unit volume. (The fluid's mass-per-unit-volume is

**a**=**F***rho*, the rate of change of our velocity is

*d*, and our force per unit volume is

**u**/dt*, plus a viscous term*

**grad**(p)*laplacian(*. The only complication is that

**u**)*d*is a total derivative, which we need to write as

**u**/dt*d*.)

**u**/dt + d**u**/d**x***d**x**/dtI won't drag you through the gory details, unless you want to see them, but it turns out that for my system the height of the fluid

*h*(measured from the coffee stirrer) versus time

*t*is \[ h(t) = h(0)e^{- t/T}, \quad T= 60.7 \textrm{sec} \times [\eta / \textrm{1 mPa*s}] \times [\textrm{ 1 g/cc} / \rho] \] [For my viscometer, the coffee stirrer has length 13.34 cm and inside diameter 2.4 mm, and the Pepsi bottle has a cross-sectional area of 36.3 square centimeters (3.4 cm inner radius). You can see how the timescale scales with these properties in the gory details section.]

Hopefully over the next couple weeks I'll try to use my viscometer to measure some interesting physics in the viscosity of fluids.

This is really cool. However...

ReplyDeleteA FEW IMPROVEMENTS TO YOUR EXPERIMENTAL DESIGN

1. It is not clear what the fluid is flowing into/onto. When measuring the viscosity of delicious fluids, I recommend placing a bowl of ice cream under the apparatus to prevent needless loss.

That is all.

Can you help me with this?

DeleteI need more details on this design

My old boss joked once in his grad-level polymer physics class that all you needed to measure viscosity was "a stopwatch, a balance, and a handy gravitational field." One of the grad students asked "where could I buy a gravitational field?"

ReplyDeleteAnyway, the above method is actually something that some of the polymer companies making polyethylene and polypropylene do to get a rough idea of the molecular weight by measuring the viscosity at a specific temperature.

C

@ Corky: The best part of your comment is that I was collecting my fluid in an empty ice cream bucket.

ReplyDelete@ C: I was thinking of using a balance, but I figured taht drawing lines on a sheet of paper was cheaper :). Also, I'd like to shove some polymer (or something) in it in the near future and show these kind of dependencies.

Water, honey, ice cream... and what about beer ?

ReplyDeleteBeer bong is a good homemade viscometer ^^

The simplest way to be able to make your own website will be to browse on the net with an online site generation application and employ one of those. You can use an online site development device in order to easily add content like links, images, videos and text for a webpages. The interfaces of these tools commonly cause whatever your content looks will you for you to look the same to all your guests. This interface trend is known as WYSIWYG, or What You Discover Is truly What You Obtain.

ReplyDeleteThis is really great. Thesis Writing

ReplyDeletenice post. Writing Services

ReplyDeleteI'm fascinated by this topic. Thanks for a great post! Very interesting to learn another way to measure viscosity without expensive instruments.

ReplyDeleteNice post, I bookmark your blog because I found very good information on your blog, Thanks for sharing more information clik more

ReplyDeleteYay for spam. :P

ReplyDeleteOtherwise, neato. Interestingly enough this is the first place where I found nice, neat collected information on a simple way to measure viscosity. All other ways ended up being... not simple and/or easy to recreate.

Thanks a lot. :)

Some of the specific details and pictures seem to be missing. Could you make them accessible again?

ReplyDeleteThis is my first time i visit here. I found so many entertaining stuff in your blog. Keep up the good work.

ReplyDeletePlastic Flow Meter

Do you love

ReplyDeleteCoke or Pepsi?PARTICIPATE IN THE POLLand you could receive a prepaid VISA gift card!If you need your ex-girlfriend or ex-boyfriend to come crawling back to you on their knees (no matter why you broke up) you need to watch this video

ReplyDeleteright away...

(VIDEO) Why your ex will NEVER come back...

ReplyDeleteNew DietTaps into Innovative Plan to Help Dieters Get Rid Of 23 Pounds within Just 21 Days!